CP2E – read user manual online or download in PDF format. Pages in total: from the Crestron website (). 2. CP2E only. 2- Series Engine. At the heart of the CP2 & CP2E is the powerful bit Freescale. Crestron CP2E Pdf User Manuals. View online or download Crestron CP2E Operation Manual.
|Published (Last):||9 February 2010|
|PDF File Size:||1.83 Mb|
|ePub File Size:||13.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cresnet device does not crextron. Every audio, video and environmental element of the home, boardroom, classroom or command center becomes integrated and accessible through the control system. If this software requires payment for a license, you may make one backup copy of the Software, provided Your backup copy is not installed or used on any CPU.
Strip and Tin Wire When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Verify that proper IR or serial port is defined. If further assistance is required, please contact a Crestron customer fp2e representative. All Crestron certified Cresnet wiring must consist of two twisted pairs. In the event that the clock fails, only an authorized technician should replace manial. For more details, refer to the Crestron Toolbox help file.
Example Program Detail View. Insulate the strip by folding a piece of? Table of Contents Add to my manuals Add. To prevent the possibility of electrical shorts, it is essential that these conductors do not touch crsetron uninsulated portion of the bussing strip. Only the required pins for each communication type should be connected. The Software is protected by copyright laws and international treaty provisions.
For additional details, download SystemBuilder from the Crestron website and examine the extensive help file. Cresnet power usage of the entire chain.
CRESTRON CP2E 说明书_百度文库
Got it, continue to print. For assistance in your local time zone, refer to the Crestron website http: Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. Apply power after all connections have been made. Reference Documents Cresnet power usage cp2s the entire chain.
Repeat the procedure for the other three conductors. This device complies with part 15 of the FCC rules. Purchasers should inquire cresstron the dealer regarding the nature and extent of the dealer’s warranty, if any. Crestron retains ownership of the Software and all copies of the Software and reserves all rights not expressly granted in writing.
Creston from the Crestron website and examine the extensive help file. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Upload program and firmware. For example, a Cresnet run using 18 AWG Crestron Certified Wire and drawing 20 watts should not have a length of run more than feet.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for cresyron it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper cpe2 procedures.
As such Crestron cannot and does not guarantee any results of use of the Software or that the Software will operate error free and You acknowledge that any development that You perform using the Software or Nanual Application is done entirely at Your own risk.
To decipher content, examine the message through the Crestron Toolbox?. One strip is supplied for each 8-position terminal block. Page 2 This document was prepared and written by the Technical Documentation department at: Individual signal generator cretsron port, allowing simultaneous firing of all ports.
Crestron CP2 Operation Manual
Page 28 Crestron Electronics, Inc. Press front panel SW-R and HW-R buttons at the same time to bypass program and communicate directly with the processor.
Comments to this Manuals Your Name. In creston event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. The strip engages the other common positions automatically. Dispose of used batteries according to the manufacturer’s instructions. Ear Attachment for Rack Mounting 2. Without prejudice to any other rights, Crestron may terminate this Agreement immediately upon notice if you fail to comply with the terms and conditions of this Agreement.
Therefore, if you use manhal PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. The Software is protected by copyright laws and international treaty provisions. To install the ears: Purchasers should inquire of the dealer regarding the nature and extent of the dealer’s warranty, if any.
Operation is subject to the following two conditions: Also See for CP2 Operation manual – 40 pages. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Operations Guide — DOC. Either add, modify, or delete entries in the IP table. The port is modem compatible modem and PC cables not included. Verify that serial cable is wired correctly for RS, mankal Use Crestron power supplies for Crestron equipment.