Posted on: July 2, 2020 Posted by: admin Comments: 0

LEXMARK X204N MANUAL PDF

View and Download Lexmark XN – X B/W Laser user manual online. User’s Guide. XN – X B/W Laser All in One Printer pdf manual download. Manuals and User Guides for Lexmark XN – X B/W Laser. We have 4 Lexmark XN – X B/W Laser manuals available for free PDF download: User Manual. View and Download Lexmark XN service manual online. XN Printer pdf manual download. Also for: Xn.

Author: Fezil Fezahn
Country: Czech Republic
Language: English (Spanish)
Genre: Medical
Published (Last): 17 March 2004
Pages: 244
PDF File Size: 15.72 Mb
ePub File Size: 6.22 Mb
ISBN: 676-2-44558-119-8
Downloads: 59217
Price: Free* [*Free Regsitration Required]
Uploader: Grok

Laser notice The printer is certified in the U. The manufacturer is lexjark responsible for safety in the event of use of unauthorized replacement parts. It is divided into the following chapters: General information contains a general description of the printer and the maintenance approach used to repair it.

Special tools and test equipment, as well as general environmental and safety instructions, are discussed.

Maintenance approach The diagnostic information in this elxmark leads you to the correct field replaceable unit FRU or part. Use the error code charts, symptom index, and service checks to determine the symptom and repair the failure.

There is no font card support. Never mix media types within a tray.

Lexmark X203N Service Manual

Tools The removal and adjustment procedures require the following tools and pexmark Unplug power from the MFP before connecting or disconnecting any cable, assembly, or electronic card. This is a precaution for personal safety and to prevent damage to the MFP. This chapter contains the codes and diagnostic tools to aid in providing corrective action for a malfunctioning MFP. Re- error results.

Paper Verify that the mylar feed strips are proprly positioned on the ADF. If the clear mylar strips are damaged, replace the Mznual. Exits a menu and returns to Ready. Start – Start a copy, scan, or fax job.

Press a second time to hang up the line. Keypad – Enter numbers, letters, or symbols on the display Shortcuts – Enters the shortcut screen Address Book – Access the stored phone numbers. Not all menus or selections will be available in all situations.

These are accessed through the driver. If the issue is not fixed, replace the controller board. No hsync received Replace the controller board.

Received request for unsupported No action needed. This topic provides maual list of all printer messages, explains what they mean, and tells how to clear the messages. The following table lists the messages manal alphanumerical order. The following actions can manuaal taken: Once the error is displayed the first time, reporting of further errors is suppressed until the printer is reset or menus are entered.

  MAHITICHA ADHIKAR 2005 PDF

When you make voltage readings, always use frame ground unless another ground is specified. Inspect the ribbon cable connection on CIS for proper connection. If connector J15 is properly connected, verify the following voltages on the controller card.

Pins 3, 6, and 8 are ground. Make sure a print cartridge assembly is installed and the cover closes all the way, engaging the cover open switch lever. Action Cover interlock switch Check lexmatk cover interlock cable to make sure it is not plugged into J9, maanual that the cooling fan cable is not plugged ito J Make sure the correct voltage fuser is being used on the MFP.

Ensure correct fuser is installed. Action Measure the resistance of the thermistor. The resistance measures from approximately 1K ohms immediately lexmqrk printing or POR to approximately K ohms when thermistor reaches room temperature. It may take 30 minutes to cool.

Replace the fuser assembly as necessary. For more network troubleshooting information, consult the Lexmark Network Setup Guide. Go to step 6. Go to step 7. Make sure the cable is plugged in securely. Check all the sensors for dirt. Pins 3, and 4 should be ground. Make sure the flag is operating freely and is correctly installed. If the sheet being fed stops momentarily, the ACM applies additional vertical force maual additional sheets to feed.

Do not mix paper types. Paper pick tires Check the tires in the ACM assembly for signs of wear or damage. Ensure cover is closed tightly. Using print quality test pages Blank page Action Toner cartridge not a Manua, Remove the toner cartridge, and gently shake it to evenly distribute the toner.

This is more noticeable as the toner cartridge nears end-of-life. If the problem continues, install a new toner cartridge. Recheck condition before replacing PC Kit if necessary. Check the transfer roll for signs of toner buildup and contamination. If the setting is not in your driver, you can download the correct Lexmark setup utility from the Lexmark Web site at www.

Go to step 2. Go to the disable scanner menu item. POR the machine into configuration mode. Verify continuity between the spring below the left side bearing and the transfer roll shaft. Go to step 8. Have the system administrator verify that Go to step 8. Properly connect the phone line to the Problem resolved. Go to step 3. Enter the Fax Go to step Go to step Verify the remote device number is not in the Banned Fax List user setting. Is the remote device number in the banned fax list?

  DULCE TORMENTO ELIZABETH LOWELL PDF

Remove the remote number from the Diagnostic aids This chapter explains the tests and procedures to identify printer failures and verify repairs have corrected the problem. Accessing service menus There are different test menus that can be accessed during POR to identify problems with the printer.

Lexmark Xn User Manual – Page 1 of 15 |

When a diagnostic test is selected from the main menu, a sub menu displays and each individual test displays in the order shown. Lexmark x54x To print the Quick Test page: Print the Quick Test Page on letter or A4 paper. The contents of the Print Test Page vary depending on the media installed in the selected input source. Any installed input tray can be tested. The pages fed through the printer are blank.

To run the Feed Test: This setting reduces speed pages per minutebut can be used to reduce curl of printed media and improve stacking in the output bin.

LEXMARK XN – X B/W LASER USER MANUAL Pdf Download.

The range is 0 default to Adjusting by one results in 9 mm of increased gap. Auto Dark Adjust This setting attempts to optimize the amount of toner used when printing with a specific operating point.

To print the event log: The following tests are available. ADF paper present – This test can be used to test the paper present sensor. Open and closed are the two states of the sensor. Select the scan first sensor test in the diagnostic menu. Toggle the sensor actuator A. The sensor will switch between the two states listed below if it is working properly: Paper is being fed from the ADF and the top edge passes over this sensor Turn off the printer, or select Exit Config Menu.

To change the setting, perform the following steps: In the configuration menu, use the arrow keys to scroll to the Disable Scanner menu item. The following hints can help you avoid jams: Make sure the stack height does not exceed the indicated maximum height. Remove the jam if you can see it.

Categories:

Leave a Comment