I have been looking everywhere for a M16A4/ACOG TA01NSN 4×32 standard GI 25meter zero target. I have seen them online but can’t find. Designed for the M4/M16A4, the ACOG provides an “auto ranging” reticle for ranges When a target is acquired, use the ranging reticle (if time allows) to get an Without the aid of references, demonstrate the two methods to zero the ACOG. feedback (Figure 10). The M Sight, RCO, when installed on a M4/M4A1/ M16A4/M16A2, is zeroed on a standard M16 zero target with alternate strike points.
|Published (Last):||25 November 2016|
|PDF File Size:||20.18 Mb|
|ePub File Size:||9.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
Many forget you looking for hits on target with a ar as intended use. Align the borelight laser with the circle on the meter target offset.
The preferred method of aiming using the M68 is to keep both eyes open, which allows a much greater field of view and makes scanning for targets much easier. With the help of an assistant, place the boresight target 10 meters in front of the weapon.
25 Meter Zeroing Targets
When this is done, move the aiming point of the aiming device to the crosshair on the meter boresight target.
The BIS is adjusted for a meter battlefield zero to provide backup in the event an optic or laser device fails to function.
All depends on what the scope is sighted for. Then again, I just shoot wildly at targets further than m because I can’t aim worth poo in Squad. If not the 25 m, acig range should we be using with the m zeroing, and what type of targets? Align the meter boresight target with the visible laser of the borelight.
Picture hosting, Exclusive club forum, Premium recognition, and more website access are only a targett away!
Practice qualification with the TWS is the same as day practice qualification with iron sights. When I go to the military range in yards, at yards roughly mI do a 6o’clock hold on a 19″ high target to get COM shots. I need to get a real Trijicon After the soldier has mastered the art of scanning he will find that targets are more easily detected by acknowledging the flicker or the movement of a target.
I helped quite a few guys dial in thier Aimpoints with a magic bullet. DenchJul 14, They are the same weapon sight, different reticule. If there is not enough ambient light to see the meter target offset circular crosshair, use a flashlight and shine targwt indirectly at the target.
FPriceJul 16, This position of the borelight, and where the visible laser is pointing, is identified as the half turn position. Dench, I got to play with the file you sent me and with the one in PDF.
Where do you aim with the ACOG? – General Discussion – Squad Forums
Although the same four fundamentals of marksmanship are used for night firing, adjustments must be made to accommodate the night vision devices.
I don’t know to upload documents I was just a dumb GM in the Navy!! So anything you can do to give yourself a few added adjustments for actual target shooting such as cmp is a good thing. Then, using a meter boresight target, the weapon can be boresighted with any optic, laser, or iron sight that the soldier is assigned to fire.
Weapon stabilization is crucial, orientation is irrelevant. I can scan one and send to you. The M68’s reflexive sight allows the soldier to fire the weapon with his cheek at a comfortable position; however, the soldier zerp zero with the same cheek position he will fire with because the parallax free is only effective beyond 50 meters.
How to Zero an ACOG Sight | Gone Outdoors | Your Adventure Awaits
Have the gunner move his reticle off the circular crosshair and then realign back on the target. While scanning the sector and or lane with the TWS, the soldier should be aware of thermal cues that allow him to detect and identify targets. When zeroing the M68, CCO at 25 meters, a designated impact zone must be identified on the meter zero target. Figure shows the current training program for these lasers. If a borelight is not available, a meter zero must zerl done to zero the device.
Mounting brackets are provided for each type of weapon. If the visible laser cannot be located when the soldier spins the borelight to the half turn position, start this procedure at 2 meters instead of 10 meters. Prev 1 2 Next Page 1 of 2.
Two soldiers a firer and a target holder are required to properly boresight a weapon.